Noodle Maker
| Nom de l'objet : | Noodle Maker |
| Titre : | Noodle Maker |
| Catégorie de l'objet : | Tools & Equipment |
| Sous-catégorie de l'objet : | Food Processing |
| Matériaux : | Wood |
| Numéro de catalogue : | C-5005 |
| Numéro d'accession : | 62-266 |
| Secteur géo-culturel : | Other Europe |
| Description : | 30 H X 20.5 W X 58.4 L, CM.. CONDITION, GOOD. NOODLE MAKER IS HOMEMADE WITH A RECTANGULAR, WOODEN, BLUE PAINTED BOX WITH A WIDER RECTNGULAR BASE, & A CRANKSHAFT, LEVERS, GEARS & CHAIN MECHANISM. END VIEW, END NEAREST BLADE- THERE ARE 2 FLAT, UPRIGHT SLIDES WELDED TO TRIPLE-SCREW-NAILED, FLAT, NARROW, STEEL BASES ATTACHED TO THE TOP SIDES OF THE BOX, CLOSE TO THE ENDS. THESE UPRIGHTS ARE HOUSED BY 2, 6.4 CM. WIDE X 17.8 CM. LONG, FLAT PIECES OF STEEL, BOLTED OPPOSITE EACH OTHER BY 2, 3/8 IN. BOLTS, HEADS FACING, WHICH ALSO ATTACH A BLADE, 13.4 CM. X 10 CM. X .2 CM., AGAINST THE BACK FLAT PIECE. WELDED TO EACH END OF THE FRONT FLAT PIECE IS A SHORT SHAFT. THERE IS A FLAT CRANKSHAFT ARM COTTER-PINNED & WASHERED TO EACH SHORT SHAFT. THE OTHER END OF EACH CRANKSHAFT ARM IS SIMILARLY ATTACHED TO THE CRANKSHAFT MECHANISM GOING THROUGH THE SIDE OF THE BOX. SIDE VIEW, CRANK SIDE - THERE IS A SHAFT END PROTRUDING ABOVE THE CRANKSHAFT. TO THE LEFT OF IT IS THE CRANK, CONSISTING OF 3.7 CM. OF PROTRUDING SHAFT WELDED TO A FLAT, CURVED ARM TO WHOSE END IS BOLTED A FLARED, ROUNDED, ROTATING WOODEN HANDLE. BELOW THE HANDLE, THE BOX SIDE HAS A 9.7 CM. X 1.2 CM., CUTAWAY AT THE BASE. ON THE UPPER LEFT OF THE BOX SIDE, A FLUSH GEAR SHAFT END IS VISIBLE. OPPOSITE SIDE VIEW - THE OPPOSITE END OF THE PROTRUDING SHAFT IS INSET ABOUT .6 CM.. THE SHAFT END OF THE CRANK IS FLUSH & SLIGHTLY MOVABLE. ATTACHED TO THE MEDDLE OF THE CRANKSHAFT ARM IS A SHORT, CURVED ARM TO WHICH IS ATTACHED A LONG, CURVED-ENDED ARM WHICH LEADS BACK TO THE GEAR MECHANISM. HERE THE LONG ARM IS CONNECTED TO A SHORT PIVOT ROD & PLATE, TRIPLE-SCREW-NAILED TO THE BOX SIDE AT THE BASE, 1 SCREW NAIL IS MISSING. ITS END IS CONNECTED BY A PIVOT TO A SHORT, STRAIGHT ARM WHICH LEADS UP TO A DOUBLE-ARMED, DOUBLE-STOPPED ROCKER MECHANISM WHICH FUNCTIONS ON A 12.5 CM. DIAMETER, FINE-TOOTHED GEAR. PARTS OF CAR IGNITION POINTS ARE USED AS TIGHTENER FOR THE LEFT STOP & AS A GEAR CATCH AT THE BOTTOM. THE RIGHT STOP HAS A 'SOUTH AMERICA' SHAPE, THIN PLATE EXTENDING OVER THE EDGE OF THE BOX END AS A TIGHTENER. TOP VIEW - THERE IS A BELT-COVERED BOARD, 51.7 CM. X 13.4 CM., INSERTED ON AN INNER SURFACE & FLUSH WITH THE LEVEL OF THE BOX. NEAR THE BLADE, A WOODEN ROLLER & STEEL SPRING BAND, WITH NAILED HOLDER PLATES, MECHANISM RUNS ON THE BELTING SURFACE. REMOVING THE BOARD, A CHANNELLED BOARD 49.2 CM. LONG SITS OVER 2 SHAFTS & SPROCKETS, A LINK CHAIN RUNNING IN THE CHANNEL. THE BOTTOM OF THE REMOVABLE BOARD HAS A CHANNEL ABOUT TWICE AS WIDE & HALF AS DEEP WITH A SINGLE COG OFFSET & SCREW-NAILED AT 1 SIDE OF THE CHANNEL NEAR ONE END. |
| Hauteur : | 30 |
| Longueur : | 58.4 |
| Largeur : | 20.5 |
| Unité de mesure linéaire : | cm |
| Nombre d'objets : | ? |
| Nombre de parties composantes : | ? |
| Étiquette ou poinçon : | UNMARKED |
| Département : | Cultural History |
| Établissement : |
Glenbow-Alberta Institute, Glenbow Museum
 Facebook-Glenbow-Alberta Institute, Glenbow Museum
 Twitter-Glenbow-Alberta Institute, Glenbow Museum
 YouTube-Glenbow-Alberta Institute, Glenbow Museum
|
| Ville de l'établissement : | Calgary |
| Province de l'établissement : | Alberta |
Coordonnées de cette page web
-
Pour proposer des corrections ou des mises à jour sur cette page, veuillez contacter directement le Réseau canadien d’information sur le patrimoine (RCIP).